• Contactless Click & Collect
  • Fast Shipping
  • 100% NZ Owned & Operated
  • Bulk Buying Discounts
Sale!

Tiger Wire Rope Puller

From $550.00 From $440.00

The Tiger manual wire rope puller is a hand operated lifting and pulling device. The puller could also be used for lowering, tensioning and guying which makes it a versatile, portable and multipurpose tool.

  • Range from 800kg to 5400kg (Lifting Capacity)
  • Lightweight manual pulling machines – simple and safe to operate
  • Compact high-strength
  • Corrosion free aluminium alloy casing
  • Steel versions also available
  • Usable at horizontal, vertical and angled working positions
  • 20m steel wire with eye hook as standard
  • Rope clamp system easily disengaged with a lever allowing smooth installation of wire rope
  • Equipped with an anchor bolt offering numerous connection possibilities
  • Overload protection built in, with a shearing pin in the forward lever
  • Shear pins can be replaced without removing the load
  • Spare shear pins supplied
  • Parallel clamping system providing evenly distributed grip at a lower force, resulting in less rope wear
  • Individually serial numbered for traceability
  • Supplied with relevant certification and user instructions
  • These units meet and exceed all the requirements within BS EN 13157:2004+A1:2009.

 

Clear
SKU: N/A

Description

The principle function of the wire puller is that the rope passes through mechanical jaws rather than being reeled on a drum of a puller or conventional winch. The tension of the rope is applied by means of two pairs of self-energized jaws which apply a grip onto the wire rope in sections. The effort is transferred to the jaws by two parallel levers, one for forward operation and the other for reverse operation. A telescopic bar, fitted to either the forward or reverse lever, transmits the effort to the jaw mechanism. This parallel clamping system provides an evenly distributed grip at a lower force, resulting in less rope wear. The load is held securely at all times.

The wire rope puller comes with a telescopic operating handle* and 20 metres of wire rope fitted with an eye-type hook as standard. Any length of rope can be supplied to your requirements. Alternatively the wire rope puller is available as a machine only, without wire rope. (*the operating handle with the 800kg TRPA/TRPS is not telescopic)

Increase the Pulling and Lifting Capacity:

Various methods of rigging are shown. For the correct and incorrect method refer to figures 1 and 2. Other methods of rigging will increase the capacity of the machine – refer to figures 3 and 4.

In examples 3 and 4 the maximum working load limit (WLL) of the pulley and anchor point shall be equal to or greater than two times the WLL.

NOTE: When the wire rope puller is anchored directly to a fixed point, ensure that there are no obstructions around the machine which could prevent the wire rope, puller and anchor from operating in a straight line.

It is recommended to use a sling of similar capacity between the anchor point and the unit.

WARNING: Any rigging configuration which requires the calculation of forces applied should be checked by a competent engineer, with special attention to the strength of the fixed point used.

Certification

Each unit comes fully certified with a test certificate or an EC Declaration of Conformity stating compliance with the essential health and safety requirements of the Machinery Directive 2006/42/EC.

Data Table

  • Code: 100749 – TRPA-08
  • Code: 100750 – TRPA-16
  • Code: 100751 – TRPA-32
  • Code: 100752 – TRPA-54

Wire Rope Puller – Aluminium Casing

 (Aluminium Casing) WLL (kg) Pulling Capacity (kg) Rope Diameter (mm) Breaking Strain (kN) Effort (kg) Advance/Pull (mm) Net Weight (kg) Overall Length (mm) Overall Height (mm) Overall Width (mm)
TRPA-08 800 1200 8.3 43 35 52 6.0 426 235 64
TRPA-16 1600 2400 11 120 41 55 11.0 545 280 97
TRPA-32 3200 4800 16 162 45 28 22.0 660 325 116
TRPA-54 5400 8000 20 264 76 30 59.0 930 480 152

Wire Rope Puller – Steel Casing

 (Aluminium Casing) WLL (kg) Pulling Capacity (kg) Rope Diameter (mm) Breaking Strain (kN) Effort (kg) Advance/Pull (mm) Net Weight (kg) Overall Length (mm) Overall Height (mm) Overall Width (mm)
TRPS-08 800 1200 8.3 43 35 52 8.0 440 265 63
TRPS-16 1600 2400 11 120 41 55 14.5 550 300 77
TRPS-32 3200 4800 16 162 45 28 28.0 690 350 91